XenonZcar Banner
Shop
XenonZcar Full Service Shop

Z31 Short Shifter Guide

The stock Z31 shifter has long, vague throws. A short shifter fixes that, and because the Z31's manual transmissions are shared with other cars, there are good off-the-shelf options for most of them. Which one fits depends on which transmission your car has.

Which Transmission Do You Have?

Z31 modelTransmissionShort shifter that fits
All non-turbo manuals, 1984-89Nissan FS5W71C ("71C")Any short shifter made for the 240SX (S12, S13, S14, S15)
Turbo manuals, 1984-86Borg-Warner T5 (FS5R90A)Any short shifter made for the 1983-2004 5-speed Mustang (T5)
Turbo manuals, 1987-89Nissan FS5R30AFew direct-fit options; see below

Your model year and whether the car is a turbo tell you which one you have, as long as the transmission hasn't been swapped. If you bought the car used, check before ordering a shifter.

1984-86 Turbo: Mustang T5 Short Shifter

The 84-86 turbo's Borg-Warner T5 shares its shifter with the 1983-2004 5-speed Mustang, so Mustang T5 short shifters bolt in. The classic choice is the B&M Precision Sport Shifter, part 45050, made for the Mustang T5 and T45. B&M rates it at about 30% less throw, and it reuses your stock knob.

The B&M 45050 has become hard to find new. Other Mustang T5 short shifters fit the same way, including the Ford Performance M-7210-M (made by Hurst), the Hurst Billet/Plus and the Steeda Tri-Ax. Check that the listing says 1983-2004 Mustang with T5, and watch out for cheap copies.

Installing it

  1. Put the transmission in neutral. Unscrew the shift knob and remove the shift boot and the console trim around it.
  2. Remove the bolts holding the shifter base to the top of the transmission and lift the stock shifter straight out. Keep a rag handy for the old grease.
  3. Clean the mounting surface and the shift rail socket, and stuff a rag in the opening so nothing falls in.
  4. Pack the new shifter's pivot with fresh grease (the kit's, or a good moly grease), remove the rag, and set the shifter in with the new gasket.
  5. Bolt it down evenly, then run through every gear, including reverse, with the engine off before you reinstall the boot, trim and knob.

Follow the instructions that come with your shifter for its bolt torque and any adjustments: some have stops you set so the lever doesn't hit the end of the gate.

Stock T5 shifter removed from a Z31
A stock T5 shifter, out of the car.
T5 shifter opening on top of the transmission with fresh grease
The shifter opening on top of the T5, greased and ready.
Aftermarket short shifter with its boot
An aftermarket short shifter with its boot.

Non-Turbo 71C: S13 240SX Short Shifter

The non-turbo Z31's FS5W71C is the same family of transmission used in the 240SX, 180SX and Silvia, so short shifters made for those cars fit. The B&M Precision Sport Shifter for the 240SX is part 45088; Megan Racing, ISR, Circuit Sports and others make 240SX short shifters too.

Installing it

  1. Put the transmission in neutral, unscrew the knob, and remove the console trim and shift boot.
  2. Remove the shift lever from the transmission following your kit's instructions, and keep track of every bushing, spring and clip.
  3. Install the new lever with fresh grease on the pivot, reusing or replacing the bushings as the kit calls for.
  4. Check every gear, including reverse, before reinstalling the boot, trim and knob.
Check the stick angle and clearance. 240SX shifters were designed for the 240SX console, so test fit before closing everything up. Some 240SX owners report having to open the tunnel hole slightly to clear a short shifter, and a few cheaper units are known to buzz or whine.

1987-89 Turbo: FS5R30A

The 87-89 turbo uses the FS5R30A, the same design as the Z32 300ZX turbo's transmission with different gear ratios. Few short shifters are made for it, and the ones that do fit are usually generic units sold for the 71C. Check fitment with the seller before you buy.

Shortening the stock lever

A common alternative on any Z31 is to take the stock lever apart and cut a section out of the stick so the shifter sits lower. Be clear on what this does: the knob sits lower and travels a shorter distance, but the lever ratio doesn't change, so it feels shorter without truly shortening the throw. A real short shifter moves the pivot, which is why it's the better fix where one is available.

Sources