XenonZcar Banner

Z32 ECU Trouble Codes: How to Read and Clear Them

You don't need a scan tool to read the engine trouble codes on a 1990–1995 300ZX. The engine computer (ECU, which the later manuals call the ECM) has a small red LED and a mode selector screw built into it. Switch it into diagnostic mode and it flashes out any stored codes, and the check engine light on the dash flashes along with it. It takes five minutes and a small screwdriver.

Years
1990–1995 (1996 below)
Where
ECU, passenger footwell
Tool
Small flat screwdriver
No faults
Code 55

Finding the ECU

The ECU sits on the passenger side, behind the trim panel in the footwell below the glove box. Remove that panel and you'll see the side of the ECU with two things on it:

  • The red LED, which flashes the codes.
  • The diagnostic mode selector, a small screw-slotted knob you turn with a screwdriver.

Early Z32 manuals mention a green and a red LED; Nissan changed this to a single red LED. The check engine light (the 1994 and later manuals call it the malfunction indicator lamp) flashes at the same time as the LED, so once the ECU is in diagnostic mode you can also count the flashes from the driver's seat.

Turn the selector gently, only as far as it goes, and always leave it fully counterclockwise when you're done. That's its normal driving position.

The diagnostic modes

The ECU has two modes, and each one does something different with the engine off (key on) and with the engine running:

Key on, engine offEngine running
Mode I (normal)Bulb check: the LED and check engine light should both be onMalfunction warning: the light comes on only if a fault is happening now
Mode IISelf-diagnostic results: flashes the stored codesO2 sensor monitor: shows whether the mixture is rich or lean

The ECU always starts in Mode I. Turning the key off resets it to Mode I once the ECU has fully powered down. You can't switch modes with the engine running.

If the LED or the check engine light doesn't come on during the bulb check, the bulb is out or something is wrong in that circuit, and the light can't warn you about faults until it's fixed.

Reading the codes

  1. Turn the ignition key to ON. Don't start the engine. The LED and check engine light should both come on (bulb check).
  2. Turn the mode selector fully clockwise.
  3. Wait at least 2 seconds.
  4. Turn the selector fully counterclockwise. The ECU is now in Mode II and starts flashing codes.
  5. Count the flashes and write the codes down (see below). The ECU repeats them over and over.
  6. Turn the key off when you're done. The ECU goes back to Mode I, and the stored codes stay in memory.

The 1990 manual also describes a check connector under the driver's side of the dash with CHK and IGN terminals. Jumping those two terminals together for 2 seconds does the same job as turning the selector.

Counting the flashes

Each code is two digits. Long flashes (0.6 second each) are the tens digit, and short flashes (0.3 second each) are the ones digit. There's a short pause between the two digits and a longer pause (about 2 seconds) before the next code.

For example, one long flash then two short flashes is code 12, the air flow meter. Three long and three short is code 33. If nothing is stored you'll see code 55: five long, five short.

Code chart, 1990–1995

Nissan added codes over the years. The 1990 manual lists the nine codes marked “1990”, the 1994 manual adds the emissions and injector codes, and the 1995 manual adds code 26 for twin turbo cars. If your car flashes a code, it can set it.

CodeWhat it meansCheck firstManuals
11Crank angle sensor circuit: no 1° or 120° signal while cranking, or too few at speedWiring and connector, then the sensor. See CAS problems.1990–95
12Air flow meter (mass air flow sensor) circuit open or shortedWiring and connector, then the sensor1990–95
13Coolant temperature sensor circuit open or shortedWiring and connector, the sensor1990–95
14Vehicle speed sensor circuit open or shortedWiring and connector, the speed sensor (reed switch)1994–95
21Ignition signal: no signal from the ignition primary circuit while cranking or runningWiring and connector, the power transistor unit1990–95
26Boost pressure sensorWiring, the sensor, its vacuum hose (twin turbo)1995
31ECU: its calculation function has failedThe ECU itself1994–95
32EGR function: the EGR valve doesn't liftEGR valve, EGR control solenoid valve1994–95
33Oxygen sensor circuit, left bankWiring, the sensor, fuel pressure, injectors, intake air leaks1994–95
34Knock (detonation) sensor circuit open or shortedWiring and connector, the knock sensor (under the intake plenum)1990–95
35EGR temperature sensor circuit open or shortedWiring and connector, the sensor1994–95
42Fuel temperature sensor circuit open or shortedWiring and connector, the sensor1990–95
43Throttle position sensor circuit open or shortedWiring and connector, the sensor1990–95
45Injector leak: fuel is leaking from an injectorThe injectors1994–95
51Injector circuit openInjector wiring and connectors, the injectors. See injector and pigtail problems.1994–95
53Oxygen sensor circuit, right bankWiring, the sensor, fuel pressure, injectors, intake air leaks1994–95
54Signal line from the automatic transmission computer open or shorted (automatics only)Wiring and connectors. See A/T fault codes.1990–95
55No faults stored1990–95

If codes 11 and 21 show up together, check the crank angle sensor circuit first. A dead CAS signal also stops the ignition signal, so fixing 11 often clears 21 too.

A code tells you which circuit the ECU didn't like, not that the part is bad. In nearly every case the manual says to check the wiring and connector first, and only replace the sensor if they're good. On a car this old, corroded connectors and brittle wiring are at least as likely as a failed sensor.

On 1994–95 cars, only some codes (12, 13, 14, 31, 32, 33, 35, 43, 45, 51 and 53) turn on the check engine light while you're driving. The others are only stored and only show up when you read the codes.

Clearing the codes

Fix the problem first, then clear the codes so you can see whether it comes back:

  1. With the key ON and the engine off, put the ECU into Mode II as above and read the codes.
  2. While it's still in Mode II, turn the selector fully clockwise, wait at least 2 seconds, then turn it fully counterclockwise. Switching from Mode II back to Mode I erases the stored codes.
  3. Turn the key off. Start the car, drive it, and read the codes again later.

Disconnecting the battery also erases them, but it can take up to 24 hours without power for the memory to clear. Always read and write down the codes before you disconnect the battery or clear anything.

Codes don't stay forever. The 1990 manual says a stored code clears itself after the starter has been used 50 times without the fault coming back. If the same fault happens again, the count starts over.

Mode II with the engine running: O2 sensor monitor

If you start the engine while the ECU is in Mode II, the LED stops showing codes and shows what the oxygen sensor sees instead. Warm the engine up and hold it around 2,000 rpm:

  • LED blinking on and off: the ECU is in closed-loop control. On is lean, off is rich. The manual's test calls for more than 5 blinks in 10 seconds at 2,000 rpm.
  • LED stays on or stays off: open loop, or a lazy or dead sensor, or a mixture that's stuck lean or rich.

Cars with two oxygen sensors show the left bank first. To switch banks, turn the selector fully clockwise, wait 2 seconds and turn it fully counterclockwise again, with the engine running.

1996: OBD-II

The 1996 300ZX moved to OBD-II. It has the standard 16-pin diagnostic connector under the dash, so any generic OBD-II scanner can read and clear its codes. They're the usual SAE “P” codes, such as P0340 for the camshaft position (crank angle) sensor, P0300–P0306 for misfires and P0420/P0430 for the catalytic converters.

The ECU still has the mode selector and Mode II, but it flashes four-digit Nissan codes on the check engine light instead of two-digit ones. The long flashes are the left two digits and the short flashes the right two: ten long and three short is code 1003, the park/neutral position switch. 0505 means no faults. The 1996 manual's diagnostic trouble code chart (EC section) lists each P code with its four-digit flash code.

Alongside the generic codes, Nissan added its own P1 codes for 1996, including the twin turbo wastegate control solenoids and boost sensor, the fuel pump control module, the cooling fan circuit and the EGR system. One worth knowing: the crankshaft position sensor on the flywheel can set a code for chipped teeth on the flywheel or drive plate, not just a bad sensor.

Clear 1996 codes with the scan tool, or by switching from Mode II to Mode I with the selector as on the earlier cars.

Consult

Every Z32 also has a Nissan Consult diagnostic port in the driver's side lower dash panel. A Consult cable with a laptop or phone app can read and clear codes and show live sensor data, which is far more useful than counting flashes when you're chasing an intermittent fault.

Sources Used

  • Nissan 1990 300ZX service manual, EF & EC section: self-diagnosis modes, the check connector, the 1990 code table and code retention. Read the EF & EC section
  • Nissan 1994 300ZX service manual, EF & EC section: diagnostic test modes, the code table, check engine light items, erasing codes and the O2 sensor monitor. Read the EC section
  • Nissan 1995 and 1996 300ZX service manuals, EC section: code 26, and the 1996 OBD-II and four-digit codes.