Z32 Non-Turbo to Twin Turbo Conversion
Turning a non-turbo (NA) Z32 into a twin turbo (TT) is one of the most asked-about Z32 projects. It can be done, but it's much more than bolting on two turbos. This page lists what's shared between the two cars, what's different, and what you can get away with keeping. It's based on the conversion notes from Z1 Motorsports, who have done many of these, checked against the factory manuals. For the basic differences between the two engines, see Engines: Non-Turbo vs Twin Turbo.
The practical approach: buy a donor car
The intercooler piping, turbo oil and water lines, brackets and dozens of small TT-only parts are hard to find one at a time, and buying them piece by piece gets slow and expensive. The usual way to do it is to buy a wrecked twin turbo or a TT front clip and move everything across. A donor also gives you the TT engine, wiring and ECU to compare against.
Engine
The same on both
- Block castings and main caps, and the oil passages in them
- Crankshaft, connecting rods (same Nissan part number), piston rings and crankshaft bearings
- Cams, lifters, valve springs, retainers and locks, with one exception (below)
- Valve sizes
- Water pump, thermostat, timing belt, PCV valves, seals, and the intake, plenum, exhaust and valve cover gaskets
- Engine mounts (and they're usually broken on an engine that comes out)
- Head gaskets: different part numbers, but they look the same
Different
- Pistons. The TT runs 8.5:1 compression against 10.5:1 on the NA. The TT piston also has an oil gallery in the crown for cooling, fed by its piston oil squirters, which point at a different angle from the NA ones.
- Heads. Similar castings, but the TT ports are more open. An NA head will work on a TT but costs some power.
- Exhaust valves. The TT uses a tougher alloy (Inconel).
- Intake cams on automatic TTs. They have less lift than the 5-speed TT and NA cams. Together with smaller turbine housings, this is why the automatic TT is rated 20 hp lower. Exhaust cams are the same on all models of a given year.
- Oil pump. On early cars the pumps are the same inside except for a stiffer pressure relief spring in the TT pump, needed to feed the turbos and oil cooler. 1994-on NA pumps and Nissan's replacement NA pumps have different, larger rounded gear teeth.
- Oil filter bracket. The TT bracket is longer and has an outlet for the oil cooler hose and a pressure valve for it. The filter bypass check valves are in the bracket on a TT and in the block on an NA. Oil filters are the same.
- Oil pan. The TT pan has extra fittings for the two turbo oil returns and the oil cooler return.
- Exhaust manifolds, turbos, and all the oil and coolant lines that feed the turbos.
- Right throttle body. Same bore, but the TT one has a junction in its coolant line to feed a turbo.
- Spark plugs. The TT takes a colder plug. See Engine differences for the factory plug numbers.
Watch the years
Upper and lower plenums are the same NA and TT for 1990–92. Nissan moved the NA to the newer injectors, lower plenum and head intake ports in 1993, but the TT didn't change until 1995. So a 1993–94 NA and a 1993–94 TT have different lower plenums and heads. The upper plenum also changed slightly in 1994 (one EGR tube flange is rotated). Match parts by year.
Fuel system
- Injectors: 370 cc on the TT against 270 cc on the NA. You need the TT injectors.
- Fuel pump: the TT pump flows much more. A healthy NA pump can usually feed a stock TT, but fitting the TT pump is cheap insurance against running lean.
- Fuel pump control unit: the 1990–93 NA runs its pump at two speeds, the TT at three. The TT controller needs a third-speed signal wire from the ECU that the NA body harness doesn't have. Z1's advice is to keep the NA controller and run the TT pump on two speeds.
- The fuel rail, filter, pressure regulator and damper are the same.
Electrical and ECU
- ECU: it needs a turbo program. Z1 recommends reprogramming the car's own NA ECU with TT settings rather than fitting a TT ECU, because the NA ECU already talks properly to the NA fuel pump controller and NA wiring.
- Engine (EFI) harness: different, but the NA harness works on a TT engine. It just has no plugs for the factory boost control solenoids, so you'll need an aftermarket boost controller.
- Interior harness and gauge cluster: leave them alone. Add a separate boost gauge if you want an accurate one.
- Shared sensors: MAF, power transistor, throttle position sensor, knock sensor, coolant temperature sensor, O2 sensors, IAA unit, AIV and EGR parts. Coil packs and starters are the same too.
- Alternator: the TT unit is 90 A against 80 A. It's interchangeable and a worthwhile upgrade.
Z1's tip for swapping the engine harness: an aluminum bracket behind the heater core and A/C evaporator, just inside the firewall, is what makes the harness hard to get out. They cut the passenger side of the bracket from the engine bay so it pivots out of the way on its remaining bolt.
Cooling and front end
- Radiator and A/C condenser: very different. The TT parts are narrower and taller so the intercooler pipes can pass on each side. The lower core support is different too (an NA one can be cut and welded to fit), and some A/C lines differ.
- Upper radiator hose is different; the lower hose is the same.
- Fan clutch: the TT one is tighter (yellow dot against an orange dot on the NA). The fan blade is the same.
- Condenser electric fan: two-speed on the TT, one-speed on the NA. The NA fan will do.
- Intercoolers and piping: the hardest part. On an NA the air goes from the filter straight to the throttle bodies. On a TT it goes to the turbos, forward to the intercoolers, then back to the throttle bodies. The NA body doesn't have the TT mounting brackets, so the piping has to be supported however you can.
- Front fascia: the TT one has openings in the lower corners to feed the intercoolers. Fascias interchange.
Nissan ran coolant through the throttle bodies to warm the intake air in cold climates. Z1 removes those lines under the plenum on conversions in warm climates, since a TT then cools the same air in the intercoolers.
Drivetrain
- Rear differential: most people keep the NA's R200V (4.083 ratio) rather than the TT's R230V (3.692). Swapping it means the whole rear subframe, the half shafts (six-bolt flange and larger splines on the TT), the hubs and the knuckles. See Differentials.
- Driveshaft: keep the NA driveshaft with the NA differential. The TT shaft has a CV joint at the diff and won't fit the NA diff. There are six different stock driveshafts (TT, 2-seat NA and 2+2 NA, each in automatic and 5-speed). They're two-piece and bolt together in the middle, so halves can be mixed.
- 5-speed: the NA and TT gearboxes share the model number, shafts, splines and ratios. The TT bellhousing is machined differently where the starter mounts, to clear the TT's larger flywheel. An NA gearbox can take the TT flywheel if you shim the starter out with washers (and sometimes grind a little inside the bellhousing). 1994-on gearboxes have stronger internals.
- Speedometer gear: it's matched to the differential ratio, so with the NA diff you keep the NA speed sensor gear.
- Clutch and flywheel: the TT clutch has a bigger friction area, a stronger pressure plate and a larger flywheel. The clutch and flywheel must match (TT with TT, NA with NA) because of the pressure plate bolt pattern.
- Clutch booster: the TT has a vacuum clutch booster with its own pedal, master cylinder and two vacuum tanks. You don't need it: with the NA pedal and master cylinder the TT clutch is just stiffer. Slave cylinders are the same.
- Automatic: the TT automatic is built heavier. An NA automatic will physically fit behind a TT engine but isn't expected to last, and the two are different lengths, so the driveshaft has to match.
Steering, suspension and brakes
- HICAS and power steering: the TT has HICAS rear steer and a two-chamber power steering pump (front steering and the rear HICAS). Keep the NA pump. Z1 doesn't recommend adding HICAS to an NA.
- Steering rack: looks and fits the same, but the NA rack is quicker to make up for having no rear steer. Leave it.
- Suspension: the same except springs, shocks (the TT has the adjustable electronic shocks) and the stiffer TT sway bars. Aftermarket parts suit either.
- Brakes: the calipers and 30 mm rotors are shared, except 1990 NAs, which used 26 mm rotors. Calipers changed from aluminum to cast iron in 1993.
- A/C compressors are the same for a given year.
Exhaust
Every section of the TT exhaust is different. US TTs have pre-catalysts right below the turbos, so their main catalytic converters are shorter. Japanese-market TTs have short downpipes instead of pre-cats, and their converter sections match the US NA ones. So with JDM-style downpipes, an NA exhaust bolts up. The TT cat-back pipes are mandrel bent and its resonator is smaller.
Sources Used
- Z1 Motorsports (300ZX.com), Z32 NA to TT Conversion information. Rewritten and summarized here; prices and product offers in the original are left out.
- Nissan 1994 300ZX service manual: compression ratios and differential ratios.