Z32 Interior Repairs
Small interior jobs that keep a Z32 cabin tidy and quiet. None of them needs special tools. They're based on Robo's write-ups from his 1992 twin turbo (credited below).
Removing the front seats
Pulling the seats is quick, and worth doing just to clean the carpet properly. If a seat suddenly won't slide, it's usually a coin jammed in the rail.
- Remove the T-tops for more room, and take out the floor mats.
- Slide the seat all the way back and remove the two 14 mm bolts at the front.
- Slide it all the way forward, fold the seatback forward and remove the two rear 14 mm bolts and washers.
- Tilt the seat up slightly and unplug the connector underneath. Both seats have one; the passenger seat's is for the seat belt warning.
- Lift the seat out with the back folded, one hand at the base of the seatback and one under the front edge. The power driver's seat is heavy; mind your back.
- On refitting, start all four bolts by hand before tightening any of them.
The carpet under the passenger seat never shows, which makes it a good donor for patches (see below) and a common hiding place for stereo amplifiers.
Removing the center console trim
Needed for stereo, switch and shifter work. All the screws in this job are the same size.
- Remove the small trim piece below the vents and stereo to expose two screws. Its clips break easily; Robo broke his off on purpose and holds the piece on with hook-and-loop tape, which makes it easy to remove again.
- Pop out the two small trim tabs (a thumbnail will do; they're fragile) and remove the screw under each.
- Pry out the center bezel around the vents and head unit. It has a couple of clips near the bottom on each side. The screws behind it only need removing for stereo or mounting-bracket work.
- Unscrew the shift knob (see below if it's stuck) and remove the front screws of the shifter cover.
- Open the ashtray, lift it out and remove the screw in the corner beneath it.
- Lift the shifter cover and unplug its connectors: shock adjuster switch, mirror switch, lighter and illumination. Canadian cars may have an extra one for the headlight washers.
- To remove the rear piece, lift the mat in the bottom of the console box, then lift and pull the piece forward. Its back edge is only tucked under the next trim piece.
Loose or crooked shift knob
If the knob is loose when its logo is straight, or only tight when it's turned off center, a little packing in the knob's threaded hole fixes it.
- Unscrew the knob counterclockwise. A badly stuck knob may only come off with a pipe wrench, which usually ruins it, so be prepared to buy a new one.
- Roll a small piece of felt into a tight ball and push it deep into the knob's hole. Felt compresses evenly and doesn't break up like paper or cardboard.
- Screw the knob back on until it's snug and straight. Don't go past straight and back off; it will lose its tightness and you'll have to start over.
- To remove old felt later, stab it near the edge with a pick and unscrew it out.
Patching a carpet tear
A hole worn or kicked through the carpet in front of the passenger seat (high heels are a common culprit) can be patched almost invisibly for nothing. Robo was quoted for a whole new carpet and $80 for a hand-stitched patch; this took about 30 minutes.
- Remove the seat and cut a donor piece from the carpet under it, a little larger than the hole. This matches the color and nap exactly. An old floor mat of a similar color works if you can't spare the donor carpet.
- Trim the donor to shape and taper its edges (fine scissors or hair clippers) so it blends into the edges of the hole from behind.
- If the donor is loop pile and the carpet is cut pile, run a craft knife through the loops to open them.
- Glue the patch in place from below with black RTV silicone, keeping the glue well away from the pile.
Repairing a broken hatch trim bracket
The center trim panel inside the hatch (it covers the lock and the reverse light access) sits on two plastic brackets at the bottom that fit over studs. People often remove only the two thumbscrews at the top and bend the panel back, which snaps the brackets off.
- Glue the broken bracket in place with super glue. It isn't strong enough on its own, but it holds the piece for the next step.
- Cut a small piece of perforated steel strap (plumbing hanger strap) and bend it to a right angle.
- Bond it across the break on the back of the panel with two-part epoxy, as a splint.
The repair is hidden once the panel is back in, and it keeps the panel snug and quiet. To remove the panel properly next time, peel back the carpet and undo the two 10 mm nuts on the bottom brackets too.
A compact flat-tire kit for the spare well
The factory can of compressed air in the spare well is decades old now and shouldn't be trusted. Aerosol sealers hold little air and coat the inside of the tire with sealant. Robo replaced the can with:
- a small 12-volt tire inflator, and
- a tubeless tire plug kit with refills.
Both fit in the spare well with the space-saver spare still on top. With them, most punctures can be dealt with at the roadside.
Related pages: Z32 Body Repairs and Upgrades, Z32 Interior Differences, Z32 Quick Fixes.
Sources Used
- Robo's Z32 tech pages, rewritten here: seat removal, console trim, shift knob, carpet repair, hatch trim bracket and flat-tire kit.