Z32 Steering Wheel and Airbag Removal
The steering wheel has to come off to recover a worn wheel, fit a refurbished one or work on the column. On airbag cars that means removing the driver's airbag first. This is based on Robo's swap on his 1995 twin turbo (credited below), with the factory manual's safety rules.
- Difficulty
- Moderate. Simple mechanically, but the airbag demands care.
- Time
- About an hour
- Special tool
- Tamper-resistant Torx T50 bit (with a hole in the tip). A plain T50 won't fit.
- Other tools
- 19 mm socket, short extension and a 1/2-inch drive breaker bar, plastic trim tool, thread locker, penetrating oil
Airbag safety
An airbag can injure or kill if it deploys while you're handling it. If you're not comfortable with that, have a professional do this job.
- Move the seat fully back, then disconnect the negative battery cable, insulate the cable end, and wait at least 15 minutes before touching the airbag. The system stores a reserve charge.
- Carry the airbag with the trim cover facing you and the metal back facing away.
- Set it down cover side up, somewhere it can't fall or be sat on. Don't store it on a high shelf, near heat, or with anything on top of it.
- Never probe the airbag connectors with a test light or meter, and never try to open the airbag unit.
- Leave the clock spring (the yellow spiral cable reel under the wheel) exactly where it is. Turning it with the wheel off can break its ribbon cable, disabling the airbag and the horn.
Which wheels fit
According to Robo, the airbag wheels from 1992 to 1996 interchange, while the earlier non-airbag wheels are a different design. A worn wheel can be sent to a trim shop to be recovered in leather; Robo matched his shift and parking brake boots to it. Wheels with spinner knobs or other adaptive equipment may have clamp marks that call for a recovered or replacement wheel.
Removing the wheel
- Point the front wheels straight ahead and mark the steering wheel's position on the shaft so it goes back on the same spline.
- Disconnect the battery and wait as described above.
- Pry off the small trim cover on each side of the wheel (marked L and R on the back) to reveal the two tamper-resistant Torx T50 bolts that hold the airbag.
- Remove both bolts and ease the airbag forward. It's easiest to unplug the two yellow airbag connectors now, with the airbag loose, rather than through the trim panel under the wheel. Handle the connectors and the flat wiring gently.
- Set the airbag aside, cover up.
- Remove the 19 mm center nut. It's tight, so use a breaker bar on a short extension.
- Pull the wheel straight off the splines. If it's stuck, a few drops of penetrating oil and patient rocking usually free it, or use a proper steering wheel puller. Don't hammer on the wheel or the shaft. Be ready for it to let go suddenly.
Refitting and centering
- Check the clock spring hasn't moved, then slide the wheel onto the splines at your mark with the front wheels straight.
- Fit and tighten the 19 mm center nut to the factory torque for your year (see the ST section of the service manual).
- Plug the two airbag connectors in fully, then seat the airbag and fit the T50 bolts with fresh thread locker. Refit the side trim covers.
- Reconnect the battery with nobody in the driver's seat. Turn the ignition on: the airbag light must come on and then go out. If it stays on or flashes, the system has a fault; have it diagnosed before driving.
- Test the horn and check the wheel is straight on a straight road. If it's off center, repeat the removal and move the wheel one spline. Robo's was one spline left and needed one spline clockwise.
If the wheel is off center but the car tracks straight, moving the wheel one spline is the fix. If it's off by less than one spline, the wheel alignment's toe setting needs adjusting instead.
Related pages: Interior Repairs, Z32 Interior Differences.
Sources Used
- Robo's Z32 steering wheel and airbag write-up, rewritten here.
- General airbag handling precautions from the Nissan factory service manual's restraint system (RS) section.