Z32 Injector Swap and Plenum Pull Checklist
The Z32's injectors live under the intake plenum. You can replace one or two without pulling it, or do the full job with the plenum off and renew everything that's hard to reach. This page covers both, plus the PRVR solenoid on top of the engine. To find a bad injector first, see Injector and Pigtail Problems. Based on Robo's write-ups from his 1992 twin turbo (credited below).
Cylinder numbering
Facing the front of the car, odd cylinders are on the right bank (passenger side, US cars) and even on the left: 1 and 2 at the front, 3 and 4 in the middle, 5 and 6 at the firewall. Injectors 5 and 6 are the hardest to reach because the long balance tube has to come off first.
Confirm the bad injector first
Injectors often fail gradually, so a weak one may read only slightly out of range or still click, just differently. Robo's advice is to confirm a suspect injector with at least two different tests before buying one:
- Listen with a mechanic's stethoscope or a long screwdriver, touching each injector at the same spot. Silent or different-sounding is suspect. Keep hair, clothing and hands away from the belts and fan.
- Click test with the engine off by turning the crank angle sensor shaft by hand (ignition on).
- Ohm test at the injector connector, engine off. Robo's working injectors read about 10 to 14 Ω.
- Power balance: with the engine warm and idling, unplug one coil pack at a time. Each should drop the idle noticeably. One that changes nothing points to that cylinder, though the cause could be the injector, its connector, the coil, the plug or low compression.
If the injectors all pass, check the coil packs. Each coil's primary should read very low resistance (the factory figure is about 0.7 Ω; subtract your meter leads' own reading). A plug that comes out wet after a short run means fuel is arriving but there's no spark.
Replacing one injector with the plenum on (the "Dremel method")
Each injector is held to the fuel rail by a half-moon cap and two screws. On some injectors one screw is hidden under a lip of the upper plenum. Grinding away a little aluminum (under 2 mm, hidden under the throttle cover) gives access without pulling the plenum.
- Best for
- One or two failed injectors when the rest are healthy. To replace all six, especially high-mileage originals, pull the plenum.
- Difficulty
- Moderate; needs patience
- Time
- About two hours, plus an overnight soak in penetrating oil
- Tools
- Rotary tool with a carbide cutter (a flex-shaft helps), shop vac, metric hex keys (ball-end hex sockets are best), needle-nose locking pliers, penetrating oil, petroleum jelly, dielectric grease
- Relieve the fuel pressure (see the warning above).
- Remove the throttle cover (four 5 mm hex screws). For injector 1, move the throttle and cruise cables and their bracket aside. Pull the oil filler cap and stuff a rag in the filler so no filings get into the engine.
- Remove the screw on the easy side first; it gives you a little play on the hidden side.
- Grind the plenum lip over the hidden screw a little at a time, vacuuming filings as you go. Sight straight down the screw between passes. Robo needed about ten grind-and-check cycles. Stop as soon as a hex key or ball-end socket fits squarely. Going through the plenum wall would need an epoxy repair, so don't rush.
- Loosen the screw gently. Original Phillips screws are often seized: soak them, use locking pliers on the screwdriver, or a manual impact driver. If they're stripped beyond that, the plenum has to come off.
- Remove the cap and soak the injector in penetrating oil (overnight if possible). Pull it out with a twisting motion, padding the pliers.
- Fit new O-rings, lubricated with petroleum jelly. Push the new injector in with a twisting motion, not straight down. A short length of 5/8-inch PVC pipe notched for the connector makes a good pusher. If it won't stay seated, the cap screws can draw it down slowly, but the aluminum threads strip easily, so don't force them.
- Fit the cap with a new upper insulator, using stainless hex screws in place of the Phillips ones. Put dielectric grease in the connector, reconnect, restore fuel pressure and check carefully for leaks before starting.
The rubber insulator in the bottom of the injector socket can't be changed this way and is reused. It's usually fine.
Injector parts (1990–1994)
| Part | Nissan part number |
|---|---|
| Lower O-ring (small) | 16618-10V00 |
| Upper O-ring (large) | 16618-10V05 |
| Upper insulator, under the half-moon cap | 16635-10V02 |
| Lower insulator, in the injector socket (plenum off only) | 16635-10V10 |
| Injector cap screw, hex-head replacement | 08360-51862 |
These are Robo's numbers for 1990–1994 cars. The 1995–1996 injectors and their seals are different; see early vs late injectors. Aftermarket stainless hex screws (M5 × 0.8, about 14 to 16 mm long) also work; don't use plain steel, which rusts in place.
Injector size: larger injectors don't add power by themselves. They let the engine make more power at higher boost without running lean. As a rough guide, an injector's cc/min rating supports about that much crank horsepower at 100% duty, and most tuners stay under about 80 to 90%. Larger injectors need matching ECU tuning; see ECU tuning.
What to replace while the plenum is off
This is Robo's "what to" list from his first plenum pull at 91,000 miles, not a full how-to. The job started with a fuel leak from the short hose joining the front of the two fuel rails, which can't be reached with the plenum on. Have a helper who has done it before, or allow plenty of time.
- Gaskets: the main plenum gasket, plus the EGR and idle air control valve gaskets for a few dollars more.
- Injectors: if they're original, seriously consider replacing all six now. When one fails, others tend to follow. Replace the upper and lower O-rings and the socket insulators on every injector. Bigger injectors mean an ECU change at the same time.
- Injector screws: swap the Phillips screws for hex-head stainless ones. The originals often strip.
- Fuel hoses: replace every rubber fuel hose you disconnect, including the rail crossover hose. Use only high-pressure fuel injection hose (5/16 inch is effectively the same as the 8 mm OEM hose). Ordinary carburetor fuel line can burst under injection pressure.
- Vacuum hoses: replace them, one at a time so you don't mix up connections. Silicone 4 mm and 6 mm hose works well.
- PCV valves and hoses: replace both valves (one each side under the plenum) with the OEM five-hose kit. A later revision adds restrictors in three of the hoses to quiet PCV noise that can sound like tappet noise (Nissan bulletin NTB91-040).
- Optional: the fuel damper and fuel pressure regulator on top of the plenum. These don't need the plenum off but are good preventive maintenance.
| PCV part (per NTB91-040) | New number | Old number |
|---|---|---|
| PCV valve assembly | 11810-40P00 | 11810-30P00 |
| Blow-by hose | 11823-30P01 | 11826-30P01 |
| Blow-by hose | 11823-30P11 | 11826-30P11 |
Numbers as listed by Robo from the bulletin. Ordering OEM should get the current parts, but check.
After reassembly the engine may run poorly for a few minutes while fuel pressure builds and the ECU settles. If it then goes into safety boost, look for a connector left unplugged; on Robo's car it was the boost solenoid on the passenger side.
Throttle body coolant bypass
Hot coolant runs through a tangle of metal pipes and hoses under the plenum to the throttle bodies. Its job is to warm the throttle shaft pivots so they can't ice up at steady highway cruise in cold, damp weather. It has nothing to do with intake air temperature. Many owners bypass it during a plenum pull by joining the supply and return with a single hose, which removes a lot of aging hose that could leak.
- If you keep the system, replace all of its hoses while you have access.
- If you bypass it, coolant hose (heater hose) is fine; it doesn't need fuel injection hose.
- The trade-off: Robo knew of one case of a briefly sticking throttle in freezing weather at highway speed on cruise control, freed by a tap on the pedal. If you drive in freezing, humid conditions, keep the system.
PRVR solenoid (warm-start stumble)
The fuel pressure regulator vacuum relief (PRVR) solenoid sits under the fuel filter bracket. For about the first 30 seconds of a warm (not cold, not fully hot) start, the ECU switches it to vent the fuel pressure regulator's vacuum line, which raises fuel pressure to prevent vapor problems. When the solenoid fails, the engine can chug badly for about half a minute after a warm start, and the cause is hard to find.
- The PRVR, AIV and EGR solenoids are the same part in different places, so a known-good one can be swapped in to test.
- Reach it by removing the fuel filter bracket bolts and lifting the solenoid bracket out from underneath.
- Robo removed his faulty system in 2003, connecting the regulator's vacuum line straight to the engine's manifold vacuum port, and reported no problems. If you do this, the fuel pressure regulator must still get manifold vacuum and boost. Never cap its line: it would run the wrong fuel pressure under boost and could lean out the engine. Replacing the solenoid keeps the system as designed.
Related pages: Injector and Pigtail Problems, Battery, Wiring and Stereo, ECU Trouble Codes, Twin Turbo Bolt-Ons.
Sources Used
- Robo's Z32 tech pages, rewritten here: injector replacement, Dremel method, testing injectors, what to replace during a plenum pull and PRVR solenoid.
- Nissan technical service bulletin NTB91-040 (PCV valve noise), as quoted by Robo.